|
1. ifconfig 查看网络装填 2. Android wifi log 过滤logcat -s mingzi 3. netstat 查看协议，网络状态 查看：protocol recv-q send-q local address Foreign address state 4. netcfg 查看网络配置类型 5. 启动（关闭）某个网络如： netcfg eth0 up（down）or(busybox ifconfig eth0 up(down)) 6. Ping 连接IP地址 7. Wpa_supplicant命令 Wpa_cli 进入wpa cilient 命令模式，help > help commands: status [verbose] = get current WPA/EAPOL/EAP status //ifname = get current interface name ping = pings wpa_supplicant //relog = re-open log-file (allow rolling logs) note <text> = add a note to wpa_supplicant debug log //mib = get MIB variables (dot1x, dot11) help [command] = show usage help interface [ifname] = show interfaces/select interface level <debug level> = change debug level license = show full wpa_cli license quit = exit wpa_cli set = set variables (shows list of variables when run without arguments) get <name> = get information logon = IEEE 802.1X EAPOL state machine logon logoff = IEEE 802.1X EAPOL state machine logoff pmksa = show PMKSA cache reassociate = force reassociation preauthenticate <BSSID> = force preauthentication identity <network id> <identity> = configure identity for an SSID password <network id> <password> = configure password for an SSID new_password <network id> <password> = change password for an SSID pin <network id> <pin> = configure pin for an SSID otp <network id> <password> = configure one-time-password for an SSID passphrase <network id> <passphrase> = configure private key passphrase for an SSID bssid <network id> <BSSID> = set preferred BSSID for an SSID blacklist <BSSID> = add a BSSID to the blacklist blacklist clear = clear the blacklist blacklist = display the blacklist log_level <level> [<times**p>] = update the log level/times**p log_level = display the current log level and log opti** list_networks = list configured networks select_network <network id> = select a network (disable others) enable_network <network id> = enable a network disable_network <network id> = disable a network add_network = add a network remove_network <network id> = remove a network set_network <network id> <variable> <value> = set network variables (shows list of variables when run without arguments) get_network <network id> <variable> = get network variables list_creds = list configured credentials add_cred = add a credential remove_cred <cred id> = remove a credential set_cred <cred id> <variable> <value> = set credential variables save_config = save the current configuration disconnect = disconnect and wait for reassociate/reconnect command before connecting reconnect = like reassociate, but only takes effect if already disconnected scan = request new BSS scan scan_results = get latest scan results bss <<idx> | <bssid>> = get detailed scan result info get_capability <eap/pairwise/group/key_mgmt/proto/auth_alg/channels/freq/modes> = get capabilies reconfigure = force wpa_supplicant to re-read its configuration file terminate = terminate wpa_supplicant interface_add <ifname> <confname> <driver> <ctrl_interface> <driver_param> <bridge_name> = adds new interface, all parameters but <ifname> are optional interface_remove <ifname> = removes the interface interface_list = list available interfaces ap_scan <value> = set ap_scan parameter scan_interval <value> = set scan_interval parameter (in seconds) bss_expire_age <value> = set BSS expiration age parameter bss_expire_count <value> = set BSS expiration scan count parameter bss_flush <value> = set BSS flush age (0 by default) stkstart <addr> = request STK negotiation with <addr> ft_ds <addr> = request over-the-DS FT with <addr> wps_pbc [BSSID] = start Wi-Fi Protected Setup: Push Button Configuration wps_pin <BSSID> [PIN] = start WPS PIN method (returns PIN, if not hardcoded) wps_check_pin <PIN> = verify PIN checksum wps_cancel Cancels the pending WPS operation wps_nfc [BSSID] = start Wi-Fi Protected Setup: NFC wps_nfc_config_token <WPS|NDEF> = build configuration token wps_nfc_token <WPS|NDEF> = create password token wps_nfc_tag_read <hexdump of payload> = report read NFC tag with WPS data nfc_get_handover_req <NDEF> <WPS> = create NFC handover request nfc_get_handover_sel <NDEF> <WPS> = create NFC handover select nfc_rx_handover_req <hexdump of payload> = report received NFC handover request nfc_rx_handover_sel <hexdump of payload> = report received NFC handover select nfc_report_handover <role> <type> <hexdump of req> <hexdump of sel> = report completed NFC handover wps_reg <BSSID> <AP PIN> = start WPS Registrar to configure an AP wps_ap_pin [params..] = enable/disable AP PIN wps_er_start [IP address] = start Wi-Fi Protected Setup External Registrar wps_er_stop = stop Wi-Fi Protected Setup External Registrar wps_er_pin <UUID> <PIN> = add an Enrollee PIN to External Registrar wps_er_pbc <UUID> = accept an Enrollee PBC using External Registrar wps_er_learn <UUID> <PIN> = learn AP configuration wps_er_set_config <UUID> <network id> = set AP configuration for enrolling wps_er_config <UUID> <PIN> <SSID> <auth> <encr> <key> = configure AP wps_er_nfc_config_token <WPS/NDEF> <UUID> = build NFC configuration token ibss_rsn <addr> = request RSN authentication with <addr> in IBSS sta <addr> = get information about an associated station (AP) all_sta = get information about all associated stati** (AP) deauthenticate <addr> = deauthenticate a station disassociate <addr> = disassociate a station suspend = notification of suspend/hibernate resume = notification of resume/thaw drop_sa = drop SA without deauth/disassoc (test command) roam <addr> = roam to the specified BSS p2p_find [timeout] [type=*] = find P2P Devices for up-to timeout seconds p2p_stop_find = stop P2P Devices search p2p_connect <addr> <"pbc"|PIN> [ht40] = connect to a P2P Device p2p_listen [timeout] = listen for P2P Devices for up-to timeout seconds p2p_group_remove <ifname> = remove P2P group interface (terminate group if GO) p2p_group_add [ht40] = add a new P2P group (local end as GO) p2p_prov_disc <addr> <method> = request provisioning discovery p2p_get_passphrase = get the passphrase for a group (GO only) p2p_serv_disc_req <addr> <TLVs> = schedule service discovery request p2p_serv_disc_cancel_req <id> = cancel pending service discovery request p2p_serv_disc_resp <freq> <addr> <dialog token> <TLVs> = service discovery resp**e p2p_service_update = indicate change in local services p2p_serv_disc_external <external> = set external processing of service discovery p2p_service_flush = remove all stored service entries p2p_service_add <bonjour|upnp> <query|version> <resp**e|service> = add a local service p2p_service_del <bonjour|upnp> <query|version> [|service] = remove a local service p2p_reject <addr> = reject connection attempts from a specific peer p2p_invite <cmd> [peer=addr] = invite peer p2p_peers [discovered] = list known (optionally, only fully discovered) P2P peers p2p_peer <address> = show information about known P2P peer p2p_set <field> <value> = set a P2P parameter p2p_flush = flush P2P state p2p_cancel = cancel P2P group formation p2p_unauthorize <address> = unauthorize a peer p2p_presence_req [<duration> <interval>] [<duration> <interval>] = request GO presence p2p_ext_listen [<period> <interval>] = set extended listen timing p2p_remove_client <address|iface=address> = remove a peer from all groups wfd_subelem_set <subelem> [contents] = set Wi-Fi Display subelement wfd_subelem_get <subelem> = get Wi-Fi Display subelement sta_autoconnect <0/1> = disable/enable automatic reconnection tdls_discover <addr> = request TDLS discovery with <addr> tdls_setup <addr> = request TDLS setup with <addr> tdls_teardown <addr> = tear down TDLS with <addr> signal_poll = get signal parameters pktcnt_poll = get TX/RX packet counters reauthenticate = trigger IEEE 802.1X/EAPOL reauthentication raw <params..> = Sent unprocessed command flush = flush wpa_supplicant state driver <command> = driver private commands 在wpa_cli 模式下输入： driver macaddr 则查看wifi mac地址
| 
